GHIDORAH 556 Placard Insert
Ghidorah 556 is a single unit, placard insert 556 magazine carrier that fits most chest rigs and plate carrier placard kangaroo pouches.
Description
More Products & Services
Products & Services
The Link-Lite
ANR Design, LLC
The Link rifle sling is a brainchild rifle sling between ANR Design LLC and Cole-Tac. The Link Sling is a 1″ webbing design rifle sling, stitched with Mil-Spec bonded Nylon thread. Mounted on the rifle, the forward section of the Link rifle sling has a 40″ length of pull, fully extended. The rear adjustment of the Link rifle sling has a 30″ total length of pull. Depending on the operator’s size, the length of pull easily allows plenty of slack to transfer the weapon system to the opposite shoulder of even the largest of end-users. The Link rifle sling is Berry Compliant and constructed of 100% US materials, assembled in New Hampshire and South Dakota at Cole-Tac facilities
ANVL UKON T2 1.93″
ANR Design, LLC
ANVL UKON 2 T2 1.93″ is a micro Aimpoint T2 type rifle mount that incorporates a single focal plane absolute co-witness backup iron sight package. FITS T1/H1. It utilizes a standard type AR-15 adjustable front sight post. It has the ability to adjust elevation. The user can adjust elevation to be point of aim, point of impact for subsonic rounds while still running the red dot for super sonic and vice versa. It can be used as an absolute co-witness as well for a backup if the red dot fails. Because it is a single focal plane, and it is so close together for a sight picture; the irons actually act like a backup red dot. The mount is constructed from 6061 aluminum with a type 3 hard coat.
Weight: 2.2oz
Height: 1.953in
Width: 1.32in
Length: 3.54in
ANR ANVL UKON Aimpoint T2 Optic Mount w/ Co-Witness BUIS 1.93
ANVL – UKON – T2 – 1.93
NSN:1240-01-710-8707
ANVL RMR UKON
ANR Design, LLC
ANVL UKON is a micro Trijicon RMR rifle mount that incorporates a single focal plane absolute co-witness backup iron sight package. It utilizes a standard type AR-15 adjustable front sight post. It has the ability to adjust elevation. The user can adjust elevation to be point of aim, point of impact for subsonic rounds while still running the red dot for super sonic and vice versa. It can be used as an absolute co-witness as well for a backup if the red dot fails. Because it is a single focal plane, and it is so close together for a sight picture; the irons actually act like a backup red dot. The mount is constructed from 6061 aluminum with a Class III hard coat.
40MM Grenade Pouch
ANR Design, LLC
The ANR Design 40mm Grenade Pouch was designed with safety in mind. The KYDEX covers the rounded projectile, in non-lethal loads; protecting the foam from getting damaged while being carried. The construction is a 2-piece KYDEX design that incorporates a corseted shock cord elastic to create user-adjustable-retention, ending in a cord-lock and a knot.
The Link – ANR Sling
ANR Design, LLC
The Link is a brainchild rifle sling between ANR Design LLC and Cole-Tac. The Link Sling is a 1″ webbing design rifle sling, stitched with Mil-Spec bonded Nylon thread. Mounted on the rifle, the forward section of the Link rifle sling has a 40″ length of pull, fully extended. The rear adjustment of the Link rifle sling has a 30″ total length of pull. Depending on the operator’s size, the length of pull easily allows plenty of slack to transfer the weapon system to the opposite shoulder of even the largest of end-users. The Link rifle sling is Berry Compliant and constructed of 100% US materials, assembled in New Hampshire and South Dakota at Cole-Tac facilities.
Mini GHIDORAH-S
ANR Design, LLC
The Mini GHIDORAH-S is a combination universal pistol magazine & rifle magazine carrier designed specifically for the Spiritus Systems JSTA. Ambidextrous design allows the end user to run each magazine either way in the carrier or flipped around; rifle magazine side forward with pistol rearward.
The Mini GHIDORAH-S fits all standard GI, Magpul, and Lancer styled magazines. Retention can be set between the pistol and rifle magazine sections. Overall fit and retention does matter, depending on how deep the end user runs the Mini GHIDORAH-S into the JSTA pouch. Retention quality will vary depending on the pistol magazine used and from which direction it faces.
R25/AR10 Universal Magazine Carriers
ANR Design, LLC
Use ANR DESIGN CNC cut, vacuumed formed SR25/AR10 Universal Rifle Mag Carrier to comfortably carry your backup magazines. Our single KYDEX rifle mag carriers provide you with increased durability and perfect retention needed for all applications. Made with the highest quality materials available, our KYDEX magazine carriers are built for hard use, standing up to the punishment of our sponsored competition shooters and everyday users. Each Rifle Mag Carrier is CNC cut and formed to order and handcrafted in the USA by ANR Design LLC.
Nidhogg Series Lightbearing Outside the Waistband
ANR Design, LLC
ANR DESIGN NIDHOGG Tactical Outside the waistband is a unique design incorporates mounting for Safariland QLS Fork, RTI hanger, and also fits the Blade Tech Tek Lok and other mounting from Blade Tech (Blade Tech mounting options not included during ordering). The Nidhogg Tactical Outside the Waistband holsters are CNC cut and vacuum formed for accuracy and precision fit. All ANR Design Nidhogg holsters are Optic cut, Suppressor Sight Height, and Threaded Barrel ready. Designed for right-handed Shooters only. Customer is responsible for sourcing their own Female RTI Disc set up, or Safariland Q22 QLS Female receptacle. We do not provide the female belt mounting options. Nidhogg holsters come with the MALE Fork or Hanger ONLY. All ANR Design holsters come suppressor sight ready up to 0.450″ tall.
AR Universal Magazine Carriers
ANR Design, LLC
Use ANR DESIGN CNC cut, vacuumed formed AR Universal Rifle Mag Carrier to comfortably carry your backup magazines. Our single KYDEX rifle mag carriers provide you with increased durability and perfect retention needed for all applications. Made with the highest quality materials available, our KYDEX magazine carriers are built for hard use, standing up to the punishment of our sponsored competition shooters and everyday users. Each Rifle Mag Carrier is CNC cut and formed to order and handcrafted in the USA by ANR Design LLC.
Standard Outside the Waistband Holster
ANR Design, LLC
Comfortably and safely Carry your firearms with our minimalistic KYDEX Holster design. Our KYDEX holsters provide you with full trigger guard protection and perfect retention. Made with the highest quality materials available, our KYDEX holsters are built for hard use, standing up to the punishment of our sponsored competition shooters and everyday users. Each OWB has adjustable retention. Our Outside the waistband holsters are designed to hug the body limiting the chance of hooking or snagging objects while performing everyday activities.
Rattler Low Vis Retention Clamp – Holster
ANR Design, LLC
Rattler Low Vis Retention Clamp was developed for a Tier 1 Unit for the purpose of the concealment of the SIG Rattler MCX under garments and a more secure way to support the SIG Rattler MCX in double velcro wall PDW Low vis bags and packs. The velcro on the holster can be sandwiched by a double wall or single wall velcro panel inside a bag to secure the small, but heavy PDW in orientations more desirable for ease of access.
NSN#:1005-01-694-7493
M203 Retention Clamp
ANR Design, LLC
The M203 Retention Clamp was born during a request from one of our Military partners needing an on-body, Soldier Systems retention system for the M203 stand alone launchers. We wanted to make the M203 Retention Clamp similar to our battle-tested Rattler MCX clamps we did for a different Military partner. We knew this style of clamp would be successful with the addition of a strap or buckle. We are using squadron material with a small, 1/2″ buckle to clasp the system. The bulk of the retention comes from the 0.125″ thick KYDEX that is vacuum formed into the ribs of the grip on the 40mm tube.
Appendix Lightbearing with Claw
ANR Design, LLC
Comfortably and safely carry and conceal your firearms with our minimalistic KYDEX Holster design. Our KYDEX CNC cut, vacuum formed Appendix Inside the Waistband holsters provide you with full trigger guard protection and perfect retention. Utilizing a Concealment Claw, this holster is designed with the highest level of concealment in mind.
ANVL UKON ACRO
ANR Design, LLC
ANVL UKON ACRO V2 is a micro Aimpoint Acro type rifle mount that incorporates a single focal plane absolute co-witness backup iron sight package. It utilizes a standard type AR-15 adjustable front sight post. It has the ability to adjust elevation. The user can adjust elevation to be point of aim, point of impact for subsonic rounds while still running the red dot for super sonic and vice versa.
Scatter Gat Trap & Sling – Shotgun Retention System
ANR Design, LLC
Scatter Gat Trap & Sling – Shotgun Retention System is a total system for retaining the shotgun weapon system on the breacher for infil, as well as, on target. The Scatter Gat Trap & Sling – Shotgun Retention System is a two part system, consisting of a combination elastic-nylon bungee sling, and a magnetized bi-fold retention system for the shotgun.
The shotgun sling has an integral section of accordion elastic, shrouded by nylon webbing, ending in 1″ webbing tail with an attached QD. The 1″ nylon webbing is purposely long so the end user can set the desired length on the QD, and cut away the excess 1″ nylon webbing. The accordion elastic section has roughly 6-8 inches of stretch. This allows the breacher to have the Scatter Gat Trap Molle mounted to the cummerbund of the plate carrier, and the grip of the shotgun tighter into the armpit/under the arm, and still allow the breacher to stretch the sling and shotgun into the appropriate position for forced entry.
The Scatter Gat Trap is a bi-fold styled shotgun retention system that physically retains the shotgun with two folds of Squadron material, bonded nylon, with a 1″ nylon webbing strap with adjustable length of pull, ending in a G-Hook. The G-Hook clasps into a loop in the Squadron trap, and can be pulled tight to retain the weapon during infil; jumping, inverted rappelling, under duress movement. Once on target, the breacher can loosen the webbing, one handed, and open the trap, exposing the shotgun. The Scatter Gat Trap has a central magnet in a magnet pouch. Once loose, the breacher can stow the loose webbing by sticking it to the magnet on the back side of the exposed Scatter Gat Trap. The shotgun is now retained to the body by a 2″ Diameter & 1/4″ thick, 50lb load magnet (note* squadron material creates a buffer between shotgun and magnet, magnetic force is in fact less than 50lb. The pouch is capable of fitting a 3/8″ thick magnet for the need of increased magnetization). The breacher can now do their duties, and quickly stick the shotgun system, by receiver or barrel assembly, to the magnet after success breach of door or structure has been accomplished; transitioning to a primary rifle. The breacher can one-handedly secure the shotgun in the Scatter Gat Trap, post breach, into the bi-fold Squadron and with the G-Hook. (The Scatter Gat Trap and handle 2″ Diameter, and 3/8″ thick magnets as well).
ANVL UKON R4T 1.93
ANR Design, LLC
ANVL UKON R4T 1.93 is a micro Sig Sauer Romeo 4T type rifle mount that incorporates a single focal plane absolute co-witness backup iron sight package. The ANVL UKON R4T 1.93″ also fits the Sig Sauer Romeo 4XT-PRO. It utilizes a standard type AR-15 adjustable front sight post. It has the ability to adjust elevation. The user can adjust elevation to be point of aim, point of impact for subsonic rounds while still running the red dot for super sonic and vice versa. It can be used as an absolute co-witness as well for a backup if the red dot fails. Because it is a single focal plane, and it is so close together for a sight picture; the irons actually act like a backup red dot. The mount is constructed from 6061 aluminum with a type 3 hard coat.
Shaman IFAK Pouch & Bifold
ANR Design, LLC
This is the Shaman IFAK pouch & bifold ONLY. The Shaman IFAK is ANR Design’s premium individual first aid kit and rapid deployment bag.
The back of the Shaman IFAK pouch has both weavable Molle-through-Squadron, as well as, 1.75″ thread-through belt loops.
The Shaman IFAK bifold and pouch is made from grommeted Squadron IR blocking material. The buckles themselves have also been treated for IR blocking. We decided to omit any First Aid Cross on the IFAK bifold and pouch; so there is no reflective material on the bifold and pouch itself. The bifold is topped with an elastic tourniquet sleeve. We believed that the presence of the tourniquet was enough to denote the contents of the pouch as an IFAK.
NICO Flash Bang Pouch
ANR Design, LLC
The ANR Design NICO Flash Bang Pouch was designed with safety in mind. The KYDEX covers the spoon and pin location to prevent accidental pin removal from the NICO Flash Bang Grenade. The construction is a 2-piece KYDEX design that incorporates a corseted shock cord elastic to create user-adjustable-retention, ending in a cord-lock and a knot.
Mission Configurable Tegris Dangler – MCTD
ANR Design, LLC
The Mission Configurable Tegris Dangler is a hole pattern matrix, or Molle/hole pattern matrix dangler that can be worn on plate carrier or chest rig. The MCTD was born from a need for a on-soldier mounting solution for a Military contract ANR was working on. It was decided to release both a MCTD in a hole pattern matrix to fit Blade Tech hole patterns. This allows the mounting of many ANR Design products including; Nico Flash Bang Pouch, 40mm Grenade Pouch, AR Universal Magazine Carriers, LMT 203 40mm Grenade Launcher RTS, and various breaching equipment holders we are working on.
Deep Concealment Pistol Magazine Carrier
ANR Design, LLC
Using our CNC Cut, vacuum formed Deep Concealment Pistol Mag Carrier, comfortably carry your backup magazines. We understand how important it is to have those extra rounds on deck and our single KYDEX pistol mag carriers provide you with that peace of mind. These carriers are molded with increased durability and perfect retention needed for all applications. Made with the highest quality materials available, our thermoplastic magazine carriers are built for hard use, standing up to the punishment of our sponsored competition shooters and everyday users. We offer the most popular selection of magazines available and rest assured these carriers are produced using the same methods as our KYDEX holsters ensuring each carrier is tested and retested before leaving the shop. Each pistol mag carrier is custom made to order and handcrafted in the USA by ANR DESIGN LLC.
Mjölnir Riser – Modular Picatinny Riser
ANR Design, LLC
P/N ANVL – Mjölnir
NSN:1240-01-710-8705
The Mjölnir Riser, a Picatinny riser, is a modular riser that has the ability to change to two different heights, 2.26″ and 1.93″ for XPS height optics, and a 2.24″ optical centerline for “low-thirds” optics. The Mjölnir Riser fits direct-to-rail mounted optics. The Mjölnir Riser optical centerline may vary depending on the mounting option of the optic being used. It was designed to have an optical centerline of 2.26″ for absolute-witness optics like the EoTech XPS® in the higher mount setting. There is a slight optical centerline shift when using a EOTech EXPS® with a centerline closer to 2.24. The Mjölnir Riser is compatible with EOTech EXPS®, Leupold LCO®, Vortex UH-1®, EOTech XPS®, Sig Sauer Romeo 8T, and other absolute and lower-thirds optics. The Mjölnir Riser’s modularity is where it shines. Designed to be compatible with Unity FAST™ LTC Magnifier Mount with EOTech EXPS®, and EOTech XPS® with their respective inserts installed, or removed. The Mjölnir Riser comes with a loose set of 10-24 x 3/8 screws to build the Mjölnir Riser in the lower, 1.93″ XPS, or 2.24″ EXPS ride height.
Description
Ghidorah 556 is a single unit, placard insert 556 magazine carrier that fits most chest rigs and plate carrier placard kangaroo pouches. It has individual adjustable retention, flared magwells for easier mag insertion, and elongated Kydex offset for the a 1″ higher ride height than standard pouches. The Ghidorah also curved to fit most plates. GHID 556 comes in black 0.080 Kydex.
NSN#: 1005-66-167-0822
Ghidorah will be provided with (qty: 6) Velcro HOOK squares that must be applied by the customer. There are many products on the market today that all follow a certain recipe of Velcro pattern. We have decided to provide HOOK only so that it is 100% compatible with our ANR/Cole-tac Kaiju Stiffy Kits. These can be found in the Store, or added-on in the Ghidorah product builder. If you want to map it to your kangaroo pouch, simply order Velcro brand adhesive hook and loop kits.
NSN#: 1005-66-167-0822
Ghidorah will be provided with (qty: 6) Velcro HOOK squares that must be applied by the customer. There are many products on the market today that all follow a certain recipe of Velcro pattern. We have decided to provide HOOK only so that it is 100% compatible with our ANR/Cole-tac Kaiju Stiffy Kits. These can be found in the Store, or added-on in the Ghidorah product builder. If you want to map it to your kangaroo pouch, simply order Velcro brand adhesive hook and loop kits.
Share
Recent Chats
Share via email
Future: handle WhatsApp here
Future: handle LinkedIn here
Future: handle Twitter here
SUBMENU HERE
Share via Chat
Copy Link