Works with following sensors:
For operation with the following sensors:

Designed for operation with devices and mechanisms, where it is necessary to check the presence of swing (slope) of movable parts.

The composition has two sensitive elements for slope recording.

The switching device can be used in industrial enterprises, infrastructure of housing and communal facilities, in hard-to-reach places (wells, basements). The switching device gives a possibility to install control measuring instruments in places with no power supply, operates in difficult climatic and weather conditions.

Features
The switching device is supplied with a 3.6 V power supply.

The power cell of the ADWANTEL TILT COUNTER switching device is a built-in battery with capacity of 1200/6000/9000/14000/19000/20000 mAh, designed for a service life of up to 10 years when counting readings and transmitting data once a day.

Counting and summing of tilts number is performed constantly. The package with the counted data is transmitted in wireless network with 1 minute period (it is not recommended to set the discreteness less than 1 minute for a long autonomous operation mode). The read data are stored in the switching device memory.

Data transmission period is configured using special commands in wireless network. By default, the manufacturer sets the data transmission discreteness to 1 time per 15 minutes. The data is transmitted according to the specified timer, which is installed in the internal memory of the switching device.

The switching device is powered by a built-in 3.6 V power supply. 20A/h cell capacity designed for 10 years.

When Prompt for Confirmation option is disabled, the switching device sends the current data to the network with the specified discreteness. There is no package delivery check in this mode. There are no untransmitted packages in the switching device memory.

The switching device communication time is controlled by LoRaWAN network server and can be set by command.

GENERAL TECHNICAL CHARACTERISTICS:

Operating temperature range t,°С: -55…+ 85
Built-in temperature sensor: Yes (sends data every time you connect)
Antenna type: internal
Power supply voltage: 3.6 V integrated power supply, capacity 20 A/h, size: D.
Built-in battery measurement: Yes (ends data every time you connect)
Casing dimensions, mm: 75х70х55
Mounting: directly to the sensor, struts to the support, to DIN-rail, wall

Works with following sensors:
Pressure sensors
Temperature sensors
Level sensors
Vibration sensors
Sensors of gas contamination (gas analysis)
Light sensors
Humidity sensors
Sensors of current and voltage/charge of the accumulator
Features
Adjustable measurement discretization from 1 time/min.
Compulsory measurement possibility
Body:
Outdoor IP66+Ex/Outdoor IP65
Power:
Autonomous

Works with following sensors:
Liquid counter
Gas counter
Electric meter (one-rate electric power metering)
Flowmeter
Mass meter
Features
Up to 8 inputs (4 optountied inputs, 4 inputs — dry contact. A possibility to choose) for one ADWANTEL Pulse device.

Body:
Outdoor IP66+Ex or IP65
Power:
Autonomous

Features
Sound alarm when activating (can be switched off)
Sending message when activating
Sending messages in duty mode about parameters of working capacity and air temperature
Constant control of leaks
Body:
Indoor
Power:
Autonomous

Works with following sensors:
ADWANTEL 1-Wire Ex autonomous switching device with digital 1-Wire temperature sensor for application in explosion hazardous zones of manufacturing facilities.

Features
1 Digital 1-Wire input
Adjustable measurement discreteness from 1 time/min
Compelling measurement capability
FEATURES:

Connection interface: 1-Wire
Communication period/battery discharge time 14 A/h: 1 min/90 days, 2 min/180 days, 10 min/300 days, 1 h/3 years 150 days
Operating temperature range t,°С: -55… +85
Device class in LoRaWAN® network: A
Activation in LoRaWAN® network: OTAA/ABP (adjustable), ALT – by default
Antenna type: internal
Transmitter output power: 25 mW (adjustable)
Sensitivity:-138 dBm
Power supply voltage: 3.6 V integrated power supply, 14 A/h capacity, size: D.
Built-in battery measurement: Yes (sends data every time you connect)
Casing dimensions, mm: 75х70х55
Mounting: directly to the sensor, struts to the support, to DIN-rail, wall
Radio range: up to 5 km in urban development; Up to 15 km in rural areas.
Body:
1ExeIICT4 Gb, IP66
Power:
Autonomous

Works with following sensors:
Controllers of various oil and gas pumping stations: centrifugal pumps, screw pumps, downhole rod pumps, other type of pump station.
Automatic-frequency control stations;
Controllers of automated group measure unit for gas measuring in oil, pump stations controllers;
Controllers of pipeline electrochemical protection;
Reagent dosing station;
Units for oil wells purifying;
Control and measuring instruments with RS-485 interface;
Any controller with Modbus protocol.
Features
Simultaneous operation with up to 64 RS-485, RS-422 devices;
Simultaneous operation with up to 16 RS-232 devices;
Control of automatic external devices.
Body:
Outdoor IP65
Power:
Autonomous

Works with following sensors:
The ADWANTEL ESD switching device is an autonomous device equipped with sensitive elements designed to monitor the safety of static objects. It allows, when installed on the protected equipment, to ensure its safety by transmitting a message about the operation of sensitive sensors installed in the switching device, responding to an attempt to dismantle or destroy the protected static equipment.
ADWANTEL ESD is a device equipped with sensitive elements recording:

– inclinations of the housing by an angle of more than 15 degrees;

– vibration and impact on the device housing;

– vibration and impact on the equipment housing to which ADWANTEL ESD is attached using piezo-electric sensor.

Features
Additionally, external fire protection sensors of the following types can be connected to ADWANTEL ESD:

Contact – control of opening of doors, gates, windows;
Movement – moving detection inside the protected area (premises, territory);
Acoustic – detection of destruction of glazed structures;
Vibration – detection of impact, increased vibration in the protected area (wall, equipment housing, perimeter fencing, pipelines, masts, etc.);
Water leak indicator – leak detection at device contact with liquid;
Gas leakage sensor – detection of increased concentration of gases (methane, propane, carbon monoxide, etc.);
Tilt sensor – response to changing position of protected equipment;
Temperature sensors – detection of temperature rise above threshold;
Smoke sensors – smoke detection in the protected area;
Manual detectors (alarm buttons) – generation of an alarm signal manually by eyewitnesses (employees, duty personnel).
Body:
Outdoor IP65
Power:
Autonomous

Works with following sensors:
Pressure sensors
Temperature sensors
Level sensors
Vibration sensors
Sensors of gas contamination (gas analysis)
Light sensors
Humidity sensors
Sensors of current and voltage/charge of the accumulator
Features
Up to 4 inputs for one ADWANTEL Analog measuring device
Adjustable measurement discretization from 1 time/min.
Compulsory measurement possibility
Body:
Outdoor IP66+Ex
Power:
Autonomous

Works with following sensors:
Opening/closing of doors, shutters, valves;
Switching on/off of electric installations (electric devices);
Detection of sensors operation;
Control of transition processes.
Features
Up to 8 inputs (4 optountied inputs, 4 inputs – “dry contact”, a possibility to choose)
Embedding into the existing metering devices and equipment
Control of automatic external devices
Body:
Indoor or Outdoor IP65
Power:
Autonomous